To configure the device to defer priority markings for packets that can defer off-channel scanning, use theĬhannel-scan defer-priority command. Service-policy (WLAN) wlan channel-scan defer-priority
CISCO IOS XE 3.2SE COMMAND LINE HOW TO
This example shows how to disable VoIP on aĭevice(config)# wlan wlan1 Device(config-wlan)# no call-snoop Device(config-wlan)# end Related References This example shows how to enable VoIP on a WLAN:ĭevice(config)# wlan wlan1 Device(config-wlan)# call-snoop Device(config-wlan)# end
See Related Commands section for more information on configuring QoS service-policy.
You must disable quality of service before The WLAN on which call snooping is configured must be configured with Platinum QoS. See the Related Commands section for more information on how to disable You must disable the WLAN before using this command. To enable Voice over IP (VoIP) snooping on a WLAN, use theĬall-snoop command. This example shows how to disable a broadcast SSID on aĭevice(config)# wlan wlan1 Device(config-wlan)# no broadcast-ssid Device(config-wlan)# end Related References This example shows how to enable a broadcast SSID on a WLAN:ĭevice(config)# wlan wlan1 Device(config-wlan)# broadcast-ssid Device(config-wlan)# end The SSIDs of WLANs are broadcasted by default. To enable a Service Set Identifier (SSID) on a WLAN, use theīroadcast-ssid command. This example shows how to disable band selection on aĭevice(config)# wlan wlan1 Device(config-wlan)# no band-select Device(config-wlan)# end Related References This example shows how to enable band select on a WLAN:ĭevice(config)# wlan wlan1 Device(config-wlan)# band-select Device(config-wlan)# end Of the same access point, and it only runs on an access point when both the 2.4-GHz and 5-GHz radios are up and running. The band-selection algorithm directs dual-band clients only from the 2.4-GHz radio to the 5-GHz radio When you enable band select on a WLAN, the access point suppresses client probes on 2.4GHz and moves the dual band clients To configure band selection on a WLAN, use theīand-select command. This example shows how to disable RADIUS server accounting on a WLAN: Device# configure terminalĭevice(config)# wlan wlan1 Device(config-wlan)# no accounting-list test Device(config-wlan)# end Related References This example shows how to configure RADIUS server accounting on a WLAN: Device# configure terminalĭevice(config)# wlan wlan1 Device(config-wlan)# accounting-list test Device(config-wlan)# end WLAN configuration Command History Release RADIUS server accounting is disabled by default. No accounting-list Syntax Description radius-server-acct To disable RADIUS server accounting, use the To configure RADIUS accounting servers on a WLAN, use theĪccounting-list command. This example shows how to disable AAA on aĭevice(config)# wlan wlan1 Device(config-wlan)# shutdown Device(config-wlan)# no aaa-override Device(config-wlan)# no shutdown Device(config-wlan)# end Related References End with CNTL/Z.ĭevice(config)# wlan wlan1 Device(config-wlan)# shutdown Device(config-wlan)# aaa-override Device(config-wlan)# no shutdown Device(config-wlan)# end This example shows how to enable AAA on a WLAN: Device# configure terminalĮnter configuration commands, one per line. See Related Commands section for more information on how to disable a
Command DefaultĬisco IOS XE 3.2SE Cisco IOS XE 3.3SE Cisco IOS XE 3.3SE This command has no keywords or arguments. To enable AAA override on the WLAN, use theĪaa-override command.